A BEGINNER'S GUIDE TO INSTALLING A BATHTUB

A Beginner's Guide to Installing a Bathtub

A Beginner's Guide to Installing a Bathtub

Blog Article

Browse Our Site

Almost everyone will have their own perception on the subject of Tools You Need to Install a New Bathtub .


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a new one is also a reasonably hard task. If the old tub is readily available, the task can move speedily; if you have to open a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will need an assistant to move out the old bathtub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and also fit attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your washroom if you have already gotten a new tub and do not require to transform the plan of your previous water system pipes.
Your tools and product checklist ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the restricted accessibility that is frequently the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
    If you need to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet as well as the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous type ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.

    Mounting the Bath tub


    Using the two wood boards under its feet, put the tub in the needed placement. The wooden boards are handy in uniformly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
    The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bathtub until the level checks out degree.
    To install taps, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
    Activate the water supply and also examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bath tub and additionally inspect the overflow electrical outlet and the normal electrical outlet for leaks.
    Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bathtub needs to wait up until the bath tub has actually been made use of a minimum of once as this will certainly settle it right into its last position.

    Planning for the Installment


    Firstly, the supporting framework provided with the bathroom should be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid pressure on the bathtub.
    Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize every one of the provided washers.
    Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealer can fracture fairly very early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant glue as well as cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    As a serious reader on How to Install a Bathtub Yourself, I think sharing that excerpt was a good idea. Loved our write up? Please share it. Help other people locate it. I am grateful for your time. Don't hesitate to pay a visit to our site back soon.


    Schedule Today!

    Report this page